prunercloud6

How to Replace a Kia Sportage Replacement Key The key of many Kia models has the keyless entry feature built into. The key is usually akin to an remote control, and can be exchanged with a fresh one from a Kia dealer or locksmith. Key fobs can stop working for a variety of reasons, such as a dead coin battery, worn buttons signal interference, water damage and a damaged receiver module. Here are some suggestions on how to get your Kia Sportage replacement key working again. How do you replace a remote key or smartkey If your Kia comes with an intelligent key, remote key, push-to-start keys, or a regular non-transponder metal key The battery inside these keys will eventually require replacement. This is especially true if your car displays a message telling you that the smart or remote keys are in poor condition. It's an easy procedure. To replace the battery in the key fob take the mechanical key from the slit in the back of the key fob. Next, lift the cover. Inside the key fob will be an incredibly small screw that holds the battery in its place. Using kia keys www.g28carkeys.co.uk , unscrew the screw and pull out the old battery. Then, you can insert the new battery and close the slit inside the key fob. Once the key fob has a fresh battery, test it by pressing the locks and unlock buttons. You're in good shape if the doors lock and unlock as expected. You can now utilize the Kia's hands-free lock/unlock feature whenever your fingers feel cold or you need to go on errands around Brandon. Note: Some key fobs might need to be programmed (transponder chips or smart keys). This requires a machine for programming that is only available to the automotive locksmith or dealer. Other keys (non-transponder metal keys) don't require programming. If you want to change the programming of your key, you'll have to write down the key code's number on the key code tag. How do you replace the battery? If the Kia key fob does not respond when you press the lock/unlock button, it's likely that the battery is low. A battery that is not functioning properly can cause other issues, like the check engine light coming on or the engine not running correctly. Fortunately replacing the battery on the key fob is a relatively simple DIY project that requires just some basic tools. Before you begin be sure that your vehicle is off and that all doors are shut. Find the small metal or plastic piece that is located at the bottom of the key fob. Then, jiggle it until the key comes out. The key can be placed inside the driver door handle to unlock your car. To replace the key fob battery, take off the cover from the back and use a plastic pry bar tool to release the latch holding the black negative battery cable. Remove the old battery and align the new battery so that the “+” positive side is facing you, and the “–” negative side is facing towards the fob's electrical contacts made of metal. Avoid using too much force when pushing the new CR2032 into place to avoid damage or bending the metal contacts. Once the new battery is installed, turn the key fob off and on in the ignition for a few times until the door locks. You can then test your Kia key fob to see whether it's functioning properly again. How can you replace the smart key? Depending on the model of your Kia Sportage, you may have the standard key fob, or a smart key. The smart key comes with an embedded mechanical key blade, while the standard keyfob does not. Both key fobs contain batteries that will eventually require replacing. Fortunately, this is a fairly simple process that only takes about two minutes. Before you get started it is important to ensure that you are on a level surface with good lighting and that the Kia is off. Remember that the fob can contain small pieces that could fall when you're not careful. The first step is to locate the small release button on the lower backside of your fob. It will be a circular button or rectangular slot. You can open the key fob by pressing the button. After the key fob has been removed, you can remove the battery that was in it. The new battery is a CR-2032 that can be purchased online or at your local auto parts store. After you've finished, you should be able to lock or unlock your vehicle using your key fob even if your engine isn't running! How to replace the mechanical key? The Kia key fob is a wonderful convenience that allows us to lock and unlock our vehicle with the press of the button. As with all devices that is used, the Kia key fob can have issues at times. There are solutions to resolve these issues and keep your key fobs running for the duration of. One of the most frequently encountered issues is a low or dead battery. This could cause your device to stop working or operate intermittently. If this happens then try replacing the battery with a new one. If this doesn't resolve the problem then try using a normal flathead screwdriver to wedge open the fob's plastic casing. Be careful not to damage any internal components or scratch the plastic. Once the battery is opened, carefully remove the battery you have been using and replace it with a brand new one. Once the new battery is in, close and then open the doors using the mechanical key (every key fob in the kia has an emergency mechanical key that will fit into the slot). Test the key fob to verify that it's functioning correctly. Contact a dealer locksmith to address the issue in the event that the key fob is not working. To avoid future lockouts, ensure you purchase an emergency key that can work in all of the trunk and door cylinders.